CDi 2302

Capacitor discharge (CD)
Mild steel Stainless steel Brass Aluminium
M3 to M8 (M10) - #4 to 5/16" (7/16")

Description

Unbeatable new power pack

  • With efficient inverter-capacitor charging technology
  • Enormous time and energy savings (30 % less energy!)
  • Highest cycle sequence of its class (up to 40 studs/min.)
  • 20 % energy reserve due to 220 V charging voltage
  • Simple operation & minimal weight (20 % lighter than previous model)
  • Extreme long life due to robust and functional industrial design

Highestlevel of quality and safety

  • IP 23 - Highest possible protection of its class
  • Capacitor formation recorded - Quality control for consistent capacitor quality through automated formation
  • Shock-proof capacitor battery - No contact of the capacitors to the device housing; sparkover (short circuit) is therefore not possible!
  • Cooling channel - Protects the electronic components from getting soiled. Ideal cooling of the inverter charging p.c. board for high sequence cycles.
Cdi2302 Re
Welding range M3 to M8 (M10 limited), dia. 2 to 8 mm (dia. 10 mm limited) / #4 to 5/16“ (7/16“ limited) , dia. 14 ga to 5/16‘‘ (dia. 3/8“ limited)
Welding rate M3 / #4 = 33 studs/min. (voltage 60 V) M8 / 5/16“ = 12 studs/min. (voltage 170 V) (M10 / 7/16“ = 9 studs/min. (voltage 210 V))
Capacitance 99000 μF
Welding time 1 to 3 ms
Energy 2400 Ws
Charging voltage 50 to 220 V (stepless voltage regulation)
Primary power 230 V/115 V*, 50/60 Hz, 10 AT (slow blow) *alternative primary power see „Order No.“
Connected load 600 VA
Power source Capacitor
Cooling type F (temperature controlled cooling fan)
IP Code IP 23
Dimension LxWxH (without handle) 480 x 205 x 250 mm / 18.90“ x 8.07“ x 9.84“
Weight 17 kg / 37.48 lbs
Suitable guns C 08, CA 08
Order No. 92-10-2302B (230 V) 92-12-2302B (115 V) 92-13-2302B (100 V)

Suitable stud welding guns:

Ca08 Re

CA 08 with foot ring

Universal design for use on flat surfaces. Used to avoid rear side marking on thin sheets. Aluminium to M6 (1/4“). Brass to M4 (#8).
Learn more
M3 to M8 (M10) - #4 to 5/16“ (7/16“)
9220285_pic_4c_rechts

CA 08 with centering tube PPR-2/CD

Used for welding with templates and for protection against spatter. Gap gun used to avoid rear side marking on thin sheets. Aluminum to M6 (1/4“). Brass to M4 (#8).
Learn more
M3 to M8 (M10) - #4 to 5/16“ (7/16“)
9220286_pic_4c_rechts_LQ

C 08 with centering tube PPR-2

Used for welding with templates and for protection against spatter. All-rounder also used for welding galvanised base material. Aluminium to M4 (#8).
Learn more
M3 to M8 (M10) - #4 to 5/16“
9220256_pic_4c_rechts

C 08 with foot ring

Universal design for use on flat surfaces. All-rounder also used for welding galvanised base material. Aluminium to M4 (#8).
Learn more
M3 to M8 (M10) - #4 to 5/16“